This article mainly introduces:

Argentina hydraulic cylinder,stainless steel cylinder manufacturer,stainless steel cylinder

(Argentina stainless steel cylinder,produced by Hengyu Hydraulic Co., Ltd）

stainless steel cylinder are widely used in Argentina，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed stainless steel cylinder for customers from Argentina.

Introduction to stainless steel cylinder:

The coordination of the sliding parts of the stainless steel cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

Piston stainless steel cylinder is widely used in hydraulic transmission. When the stainless steel cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the stainless steel cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the stainless steel cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

The assembly work of the stainless steel cylinder has a great impact on the quality of the stainless steel cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Answers to some questions about stainless steel cylinder:

How to disassemble the big nut that excavate the oil cylinder piston of the excavator?
If you want to be safe, look for a special unloading place for this thing, which is an oil cylinder on top of a turntable with a large nut attached to the center of the turntable. If you're in the field just pin the head of the cylinder to one end, use a big homemade wrench to hold the nut in place, and then get a digging machine and push it down, and it opens.

Classification and application of cylinders.
Hydraulic cylinder is divided into single acting hydraulic cylinder, double acting cylinder, combined hydraulic cylinder, swing hydraulic cylinder. Single acting cylinder is divided into plunger type hydraulic cylinder, single piston rod hydraulic cylinder, double piston rod hydraulic cylinder, telescopic hydraulic cylinder. Plunger type hydraulic cylinder: the plunger moves only in one direction, and the return stroke is to push the plunger back using its own weight or load. Single piston rod hydraulic cylinder: The piston moves only in one direction, and the return stroke is to push the plunger back using dead weight or load. Double piston rod hydraulic cylinder: both sides of the piston are equipped with piston rods, and pressure oil can only be supplied to one side of the piston. The return stroke usually uses spring force, gravity or external force. Telescopic hydraulic cylinder: It obtains long stroke with short cylinder. The hydraulic oil is pushed out from large to small section by section, and the external force is reduced from small to large.