This article mainly introduces:

Argentina hydraulic cylinder,200 ton hydraulic cylinder manufacturer,200 ton hydraulic cylinder

(Argentina 200 ton hydraulic cylinder,produced by Hengyu Group）

200 ton hydraulic cylinder are widely used in Argentina，because of high work efficiency，long service life，smooth movement.So our company has designed 200 ton hydraulic cylinder for customers from Argentina.

Introduction to 200 ton hydraulic cylinder:

When the 200 ton hydraulic cylinder needs to be stored for a period of time, please follow the recommended methods: The 200 ton hydraulic cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the 200 ton hydraulic cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil 200 ton hydraulic cylinder should not be in direct contact with water vapor for a long time. The 200 ton hydraulic cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the 200 ton hydraulic cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the 200 ton hydraulic cylinder Before working, the 200 ton hydraulic cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the 200 ton hydraulic cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

When the 200 ton hydraulic cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the 200 ton hydraulic cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

In the process of using the 200 ton hydraulic cylinder, sometimes such a problem will occur, the 200 ton hydraulic cylinder can not act immediately after the instruction of the 200 ton hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil 200 ton hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

Before the 200 ton hydraulic cylinder is removed, the system should be unloaded, the loop pressure is zero, the oil source should be cut off, and the oil port should be blocked after the oil port distribution pipe is loosened.

Answers to some questions about 200 ton hydraulic cylinder:

What is a variable amplitude cylinder?
The type of variable amplitude cylinder is: double acting piston type cylinder, single acting plunger type cylinder, double acting two-stage telescopic cylinder. Double acting piston cylinder is the most common application. The oil cylinder has two oil outlets, and when the oil is fed into the A port, the oil is returned to the B port; If the oil inlet of the B port is returned to the oil of the A port, the reciprocating movement of the piston depends on the effect of pressure. Single-acting plunger (or piston) cylinder has only one oil port, the pressure oil can only supply oil to one side of the plunger in the cylinder, the plunger moves in one direction under the action of pressure oil, and the return stroke of the plunger is driven by the gravity of the lifting arm, such as the LT1040 truck crane variable amplitude cylinder. The double-acting two-stage telescopic cylinder is a set structure, and the two-stage piston rod is like a tie rod antenna set in the cylinder barrel.

What is the principle of electric cylinder?
Principle: The electric cylinder converts the rotating motion of the motor into the linear motion of the push rod through the mechanical movement of the lead screw and the lead screw pair. With the closed-loop control characteristic of servo motor, the precise control of thrust, speed and position can be realized easily. Using modern motion control technology, numerical control technology and bus (network) technology, the program and bus (network) control is realized. Because of its easy control and use, it will realize the precision motion control that the cylinder and hydraulic cylinder drive can not achieve. Electric cylinder application field: 1, coordinate manipulator: logistics transmission, automated production line. 2. Wave making machine. 3, parallel mechanism: experimental platform, simulation platform, antenna. 4. Parallel machine tools. 5. Medical equipment: CT, Kamar